Tech Uber - Part 90

Tenergy Smart Universal Charger for NiMH/NiCD Battery Packs: 7.2v – 12v

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

Best Charger for charging all RC Car, RC Airplane and Airsoft battery packs 7.2V, 8.4V, 9.6V and 12V. Universal for any NiMH /NiCd battery packs 7.2V – 12V (6-10 Cells pack) Fast charger with current switch to select either, 0.9A and 1.8A. Delivers full charge within 1 – 2 hours.Charging Current 0.9A for battery packs with capacity from 900mAh -1800mAh. Charging Current 1.8A for battery packs with capacity above 2000mAh. For 3000mAh pack, charging time is 1.5 hours.Smart Charger with automatic voltage detection.Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life. Red LED will be on during charging. Automatically charging ending with negative delta V. 4 hour safety timerCharger will stop charging after 4 hours of operation.Worldwide usage with 120-240V AC With Temperature sensor Safety protection fuse for over current, short circuit & reverse polarity protection. Weight10.7 ozAccessories Included1 standard Tamiya connector. 1 connector adapter from standard Tamiya to Mini Tamiya. 1 set of alligator clip adapter with standard Tamiya connector on one end. 1 Temperature sensor Smart Charger SpecificationFOR 7.2V-12V NI-MH/NI-CD BATTERY PACK 6-10PCS BATTERYInputAC100-240VOutput7.2-12V 0.9or1.8AOperation InstructionConnect battery pack to output connector and plug AC power source. Make sure battery polarity is connected correctly (Red wire is positive) Charger will detect battery voltage automatically, Red LED will be on during charging When battery is fully charged, current will reduce to trickle charging at 50mA, Green LED will be on Battery will be charged at 0.9A or 1.8A constant current, Approximate Charging time is about 1.5hrs for 3000mAh battery,1hr for 1800mAh battery. The charger is designed for faster charging NiCd and NiMH battery packs from 6 to 12V for RC car/Air and Air soft gun. Don't charge battery packs with voltage less than 6V or voltage greater than 12V and capacity smaller than1100mAh. Battery pack must be made by high drain current cell. Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misusage. CautionThe charger is designed for indoor use only. Don't leave the charger unattended during charging.The Charger should be positioned horizontally and work in well ventilated condition, avoid water and keep away from flammable explosive goods. Don't cover the charger when charging, ambient temperature shall not be more than 40oCDon't touch the plug. Don't leave the batteries and chargers on wood surface or carpet.Cut off the power supply before connect or disconnect the charger with batteries. Don't try to disassemble the charger, High voltage inside, danger!Download product data sheet here.

Price: $22.95

3173997-10491244?url=http%3A%2F%2FWWW.ALL-BATTERY.COM%2FTenerg12v-24vNiMH_NiCDCharger-01027.aspx%3Fzmam%3D55942680%26zmas%3D1%26zmac%3D17%26zmap%3D1027

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

http://www.all-battery.com/productimages/charger/01027-Charger-for-12V—24V-nimh-&-nicd-battery-pack—universal-smart-charger 1×250.jpg

Price: $

Tenergy Smart Universal Charger for NiMH/NiCD Battery Packs: 12v-24v

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

:Best Charger for charging all RC Car, RC Airplane and Airsoft battery packs 12V – 24V. Universal for any NiMH /NiCd battery packs 12V – 24V (10-20 Cells pack).100-240V AC input for worldwide use – 500mA charging current.Designed for use with 12V – 24V battery packs (please don't charge battery pack under 12V or over 24V).Green LED will flash slowly when no battery is plugged in, Red LED will be on during charging. Green LED will be on when battery is fully charged. Red LED will rapidly flash when the charger is short circuit, Red LED will flash if polarity is reversed or the battery is non-rechargeable.Automatically cut-off by negative delta V detecting or when battery's temperature is over 60C; when battery pack gets fully charged, Green LED will be on.15-hour safety timer, charger will stop charging after operates 15 hours.One standard Tamiya male connector installed with the charger.One set of alligator clip adapter with female tamiya connector included for charging other type of battery packs.One adapter from standard male Tamiya to mini female Tamiya for charging airsoft gun battery packs.Includes:1 standard Tamiya connector. 1 connector adapter from standard Tamiya to Mini Tamiya. 1 set of alligator clip adapter with standard Tamiya connector on one end. 1 Temperature sensor. Smart Charger SpecificationInputAC100-240VOutput12-24V Dimension119(L) x 61(W) x 38(H)mmWeigh236gOperation InstructionConnect battery pack to output connector and plug AC power source. Make sure battery polarity is connected correctly (Red wire is positive). Put the temperature sensor onto the middle surface of battery pack with rubbberized fabric (refer to the following temperature sensor usage demonstration).When charger is connected to the AC source, the green LED flash.After charger is connected to correct battery pack, the red LED will be on to show that it is charging.Warning:DO NOT operate the charger when temperature is higher than 40C; we recommend you operate when the temperature is lower than 35C due to batteries becomming warm during charge.Highly recommend using Tenergy brand NIMH/NICD battery pack. We are not responsible for any damage caused by charging other brand battery using this charger.Pay attention to battery surface temperature; stop charging when it is over 60C or it feels very hot.Please always use temperature sensor during charge.The charger is designed for indoor use only; don't leave the charger unattended during charging.The Charger should be positioned horizontally and work in well ventilated condition, avoid water and keep away from flammable explosive goods.Don't touch the plug. Don't leave the batteries and chargers on wood surface or carpet.Cut off the power supply before connect or disconnect the charger with batteries. Don't try to disassemble the charger, High voltage inside, danger! Download product data sheet here.

Price: $22.95

Tenergy 6V 3300mAh Side by Side NiMH Battery Receiver Packs with Hitech Connector

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

Product6.0V 3300mAh NiMH BatteryMakeMade of Nimh Sub C 5 cellsConnectorUniversal ConnectorFit ModelsFit 1/5 Scale vehiclesFG model sport, RedCat,etc.FeatureRapidly charges and has a long life cycleWeight10 OzDimensions4.38″ (Long)0.9″ (Height);1.8″ (Width)

Price: $22.99

AT: Tenergy 7.2V 1600mAh Micro NiMH Battery Pack for 1/18 Scale Cars like Losi Mini-T

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

7.2V 1600 mAh NiMH Battery PackMade of 6 x 2/3A 1600 mAh NiMH cells.With 1/18 Car connector .Great For 1/18 Scale Cars like Losi Mini-T, and other micro vehicles. Extreme duration and performanceHigh performance with high capacity.This pack should be used for sport not racing.Dimension66L x 45W x 17H mm Weight4.5oz6 months warranty.

Price: $22.99

Tenergy 7.2V 3800mAh High Power Flat NiMH Battery Packs for RC Cars and Sumo Robots

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

High Capacity High Power Nickel Metal Hydride Battery Pack for RC cars.NiMH technology enables convenient charging at any time. No cell memory effect. No need to fully discharge before recharging.High power delivery with 30 Amp maximum discharge rate. (Tamiya max current 30A)Uniquelydesigned& manufacturedfor high RC Racing performance.Fits with popular standard 7.2V RC cars like Traxxas, LOSI, Associated, HPI, Tamiya, Kyosho, etc.6 months warranty.Technical SpecificationsStandard Dimension5.39″x1.87″x0.95″ inch, fits all RC10 carsWeight13.5 OzCapacity3800 mAhVoltage7.2VStandard Charge12 hours @ 300 mARapid Charge:1.5 hours @ 3000 mA

Price: $22.99

Tenergy Smart Universal Battery Pack Charger: 12V – 16.8V

Posted by TechUber on Dec 11, 2011 in Batteries | 0 comments

Best Charger for charging all NiMH/NiCD battery packs 12V,13.2V,14.4V,15.6V,16.8VTemperature sensor to offer 2nd level over charge protectionUniversal for for any NiMH /NiCd battery packs 12V – 16.8V (10-14 NiMH/NiCD Cells packs) Fast charger with current switch to select either, 0.9A and 1.8A. Deliver full charge within 1 – 2 hours. Charging Current 0.9A for battery packs with capacity from 1100mAh -2200mAh. For 2000mAhpack, charging time is 1 hour. Charging Current 1.8A for battery packs with capacity above 2000mAh. For 3000mAh pack, charging time is 1.5 hours. Smart Charger:with automatic voltage detection. Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life. Red LED will be on during charging. Automatically charging ending with negative delta V. Worldwide usage with 120-240V AC Safety protection fuse for over current, short circuit & reverse polarity protection. Accessories Included 1 standard Tamiya Female connector and Fuse house with the smart battery charger. 1 connector adaptor from standard Male Tamiya to Mini Female. 1 set of clip adaptor with Male Tamiya connector on one end. 2 additional fuses Smart Charger Specification FOR 12V-16.8V NI-MH/NI-CD Battery Packs (10-14 Cells in series ) InputAC100-240V Output12V-16.8V 0.9 or 1.8A Dimensions11.7 x 5.8 x 3.6 cmOperation InstructionConnect battery pack to output connector and plug AC power source. Make sure battery polarity is connected correctly (Red wire is positive) Charger will detect battery voltage automatically, Red LED will be on during charging When battery is fully charged, current will reduce to trickle charging at 50mA,Green LED will be on Battery will be charged at 0.9A or 1.8A constant current, Approx, Charging time is about 2 hrs for 3000mAh battery,1.5hr for 1800mAh battery. Don't charger battery pack with voltage less than 12V or Voltage bigger than 16.8V and capacity less than 1100mAh. Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misusage. CautionThe charger is designed for indoor use only. The Charger should be positioned horizontally and work in well ventilated condition, avoid water and keep it away from flammable explosive goods. Don't cover the charger when charging, ambient temperature shall not be more than 40oC Don't touch the plug. Cut off the power supply before connect or disconnect the charger with batteries. Don't try to disassemble the charger, High voltage inside, danger!